Jet Tools JWL-1642EVS-2 User Manual

Operating Instructions and Parts Manual Wood Lathe Models: JWL-1642EVS and JWL-1642EVS-2 WMH Tool Group 2420 Vant

103. Lift the tailstock end of the lathe up far enough to slide a few pieces of scrap wood under the leg, see Figure 2. 4. Thread adjustable feet

11Guard 1. Attach guard to the bracket by inserting the rod and lifting up on the plunger (A, Fig. 5). 2. There are two detents that will hold th

128. Headstock Faceplate: (K, Fig. 8) Used for turning bowls and plates. There are a number of screw holes for mounting the workpiece. Thread the fa

13Speed Change 1. Disconnect the machine from the power source! 2. Loosen the locking handle (A, Fig. 11). 3. Lift up on the tensioning handle

14Mounting Workpiece Between Centers Spindle turning takes place between the centers of the lathe. It requires a spur center in the headstock and a

15Stock Selection Stock for spindles should be straight grained and free of checks, cracks, knots and other defects. It should be cut 1/8" to 1

16Coves 1. Use a spindle gouge. With the flute of the tool at 90 degrees to the workpiece, touch the center of the cutting edge to the workpiece an

17Sanding and Finishing Leaving clean cuts will reduce the amount of sanding required. Adjust the lathe to a finishing speed, and begin with fine sa

18Face Plate or Chuck While faceplates are the simplest, most reliable method of holding a block of wood for turning, chucks can also be used. A chu

19To Shape the Outside of a Bowl 1. Odd shaped burls, crotches and other irregular shaped blanks require special preparation before mounting in a ch

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Serv

20To Shape the Interior of a Bowl 1. Stop the lathe and move the tailstock away. Remove the center from the tailstock to prevent bumping it with yo

21Adjusting the Clamping Mechanism The clamps are pre-set at the factory and should not need any adjustment. However, if adjustment is needed remove

22 Troubleshooting Problem Possible Cause Solution Excessive vibration. 1. Workpiece warped, out of round, has major flaw, or was improperly prepa

23Stand and Bed Assembly

24Stand and Bed Assembly Index Part No. No. Description Size Qty. 1... JWL1642-201 ...I.D. Label...

25Headstock Assembly

26Headstock Assembly Index Part No. No. Description Size Qty. 1... JWL1642-101 ...Headstock ...

27Headstock Assembly (continued) Index Part No. No. Description Size Qty. 47... JWL1642-147 ...O-Ring...

28Wiring Diagram for JWL-1642EVS

29Wiring Diagram for JWL-1642EVS-2

3 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. This wood lathe is designed and intended for use

30Indexer Positions How to use the chart A diagram of the indexer is shown at right, as viewed from the tailstock end of the Lathe. Points A, B and

31Notes:

32 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com

4 SPEED RECOMMENDATIONS Diameter of Work Roughing RPM General Cutting RPM Finishing RPMUnder 2" 1500 3000 30002 to 4" 600 1500 23004 t

5Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or break

6230-Volt Operation (Model JWL-1642EVS-2 only) 1. A plug with a UL/CSA listing suitable for 230V operation (Figure D) must be connected to the powe

Introduction This manual is provided by JET covering the safe operation and maintenance procedures for Models JWL-16423EVS and JWL-1642EVS-2 Wood Lat

8Specifications JWL-1642EVS JWL-1642EVS-2 Stock Number.....

9 WARNING Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious in