Jet Tools JWTS-10 User Manual

Operating Instructions and Parts Manual Table Saw Model: JWTS-10 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-708100 Ph.

10 Hardware The shipping carton includes two hardware bags with parts for assembling the JWTS-10 Table Saw. Hardware bag JWTS10-HP contains six packe

11 Assembly Read and understand all assembly instructions before attempting assembly! Failure to comply may cause serious injury! Unpacking and Cl

12 Assembling the Saw to the Stand Do not plug the table saw into the power source until all assembly has been completed! Failure to comply may cau

13 Handwheels Referring to Figure 6: The JWTS-10 Table Saw comes equipped with two handwheels which look identical except for the mounting holes as f

14 Front Guide Rail Referring to Figure 9: Required Fastening Hardware (see also inset): A – 6 ea – Square Head Bolt (M8) B – 6 ea – Lock Washer (M8)

15 Switch Bracket Referring to Figure 11: 1. Insert two M6x12 pan head screws (A) through the back of the switch bracket mounting holes (B). Place M

16 Installing/Replacing the Blade When installing or changing the saw blade, always disconnect the saw from the power source! Failure to comply cay

17 Table Insert Referring to Figure 16: 1. Raise the blade guard assembly. 2. Lower the blade completely. 3. Place the table insert (A) into the op

18 This fence is positioned by lifting up the lock handle (A, Fig. 19) and sliding to the desired location. "Fine-tuning" is accomplished

19 Grounding Instructions 1. All Grounded, Cord-connected Tools: In the event of a malfunction or breakdown, grounding provides a path of least resis

2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Serv

20 Adjustments Blade Raising and Tilt Mechanism Never try to force the tilting mechanism past the 45º or 90º stops! This may cause the blade to go o

21 Operations Table Saws Familiarize yourself with the location and operation of all controls and adjustments and the use of accessories such as the

22 Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure

23 When ripping long boards, use a support at the front of the table, such as a roller stand, and a support or "tailman" at the rear as sho

24 To improve the effectiveness of the miter gauge in crosscutting, some users mount an auxiliary wooden extension face (with a glued-on strip of san

25 Dado Cutting – Dadoing is cutting a wide groove into a workpiece or cutting a rabbet along the edge of a workpiece. A dado insert, shown in Figure

26 Filler Piece A filler piece (Figure 40) is necessary for narrow ripping and permits the blade guard to remain on the machine. It also provides spa

27 Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Clean

28 Troubleshooting Symptom Possible Cause Correction Low voltage. Check power line for proper voltage. Motor will not start Open circuit in motor o

29 Parts JWTS-10 Table and Cabinet Parts List Index No. Part No. Description Size Qty 1...JWTS10-301...Table...

3 Table of Contents Table of Contents...

30 JWTS-10 Table and Cabinet Exploded View

31 Motor and Trunnion Assembly Parts List Index No. Part No. Description Size Qty 1...VB-A31 ... Belt...

32 Motor and Trunnion Assembly Parts List Index No. Part No. Description Size Qty 55...JWTS10-155... Wave Washer...

33 Motor and Trunnion Assembly Exploded View

34 Fence and Rail Parts List Index No. Part No. Description Size Qty ...JWTS10-FA...Fence Assembly (#1 thru #39)...

35 Fence and Rail Parts List Index No. Part No. Description Size Qty 53...JWTS10-253... Rear Rail, Long...

36 Stand Assembly Parts List and Exploded View Index No. Part No. Description Size Qty 1...TS-1540061... Hex Nut1**...

37 Wiring Diagram 200MFD 250 VAC200MFD 250 VACWHITEBLACKBLACKWHITEGREENGREEN30MFD 350 VACELECTRICAL SCHEMATIC - 115V RED YELLOW BLACK

38 Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST), Monday through Fri

39 Notes

4 Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on

40 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com

5 Error! Objects cannot be created from editing field codes. 21. Provide for adequate space surrounding work area and non-glare, overhead lighting. 2

6 The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the

7 Features Specifications Model Number...

8 Definitions And Terminology Arbor: Metal shaft that connects the drive mechanism to the blade. Bevel Edge Cut: Tilt of the saw arbor and blade bet

9 Shipping Contents Carton Contents 1 ea Table Saw (not shown) 1 ea Front Rail – Long (A) 1 ea Front Rail – Short (B) 1 ea Extension Wing – Left