Jet Tools JWBS-14DX User Manual

Operating Instructions and Parts Manual 14-inch Deluxe Band Saw Models: JWBS-14DX WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part

Fasteners for JWBS-14DX A. Saw Body to Stand 4 – M8x40 hex cap screws (approx. 1-1/2" long) 8 – M8 flat washers 4 – M8 lock washers

11Receiving Open both shipping containers and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Re

12 WARNING Saw body is heavy! Use caution when lifting and stabilize until firmly attached to the stand! Failure to comply may cause serious injur

139. The v-belt is properly tensioned when finger pressure between the two pulleys causes approximately 1/2" deflection (fig. 8d).

1413. To mount the table, remove pin and insert from the table (Fig. 13). 14. Rotate the table so that the saw blade will slide through the slot

15Adjusting 90°°°° Table Stop 1. Disconnect machine from the power source. 2. Loosen lock knobs (Fig. 14) and tilt table left until it rests agai

169. Tension and track blade before operating saw. Find instructions for tensioning and tracking the blade under "Adjusting Blade Tension"

17Adjusting Upper Blade Guide Assembly 1. Disconnect machine from the power source. 2. Loosen lock knob (A, Fig. 18) and raise or lower upper bla

189. The blade support bearing should be adjusted so that the back edge of the blade overlaps the front face of the ball bearing approximately 1/8&q

19TROUBLE-SHOOTING (JWBS-14DX Band Saw) PROBLEM POSSIBLE CAUSE SOLUTION Saw stops or will not start 1. Saw unplugged 1. Check plug connectio

2 This manual has been prepared for the owner and operators of a JET Model JWBS-14DX Band Saw. Its purpose, aside from proper machine operation, is

20Parts Breakdown JWBS-14DX Body Assembly

21Parts List JWBS-14DX Body Assembly Index Part No. No. Description Size Qty. 1 ... 150100AW ...Upper Arm Frame ...

22Parts List JWBS-14DX Body Assembly Index Part No. No. Description Size Qty. 51...992009... Key...

23Parts List JWBS-14DX Body Assembly Index Part No. No. Description Size Qty. 101... 150101 ...Lower Wheel Blade

24 Parts Breakdown JWBS-14DX Closed Stand Assembly

25 Parts List JWBS-14DX Closed Stand Assembly Index Part No. No. Description Size Qty. 1 ... 150501W...Stand ...

26 Optional Accessories for JWBS-14DX Band Saw 708114 Three speed kit for WBS-14CS Produces speeds of 965, 1470, and 2465 SPFM. Includes four

27 JWBS-14DX Electrical Schematic – 115V

28 JWBS-14DX Electrical Schematic - 230V WMH TOOL GROUP 2420 Vantage Drive Elgin, IL 60123 Ph: 800-2

3 Table of Contents Warranty...

4 WARNING As with all machines, there is a certain amount of hazard involved with the use of this band saw. Use the machine with the respect and cau

5• SECURE WORK. Use clamps or a vise to hold the work when it’s practical. It’s safer than using your hand and it frees both hands to operate the

6SAFETY DECAL Familiarize yourself with the location and content of this decal on your machine. Fig. 1

Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction

8230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the po

9Specifications: JWBS-14DX Band Saw Stock Number .......................